Reproduction Parts for 1916-1964 Chevrolet Passenger Cars & 1918-1987 Chevrolet & GMC Trucks


Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Jan 2023
Posts: 4
Grease Monkey
OP Offline
Grease Monkey
Joined: Jan 2023
Posts: 4
Hello all - I will keep the stock brakes and suspension and want to upgrade the wheels and tires for highway travel, long road trips. I am not aware of size limitations due to fender clearance, suspension travel, etc. No, I am not autocrossing like I used to in a 69 Stingray, but "agile" driving appeals to me. So, I am seeking information as to wheel dimensions, tire sizing, and the bolt hole pattern. Thanks in advance.

Cheers!
Boltgunner

Filling Station - Chevrolet & GMC Reproduction Parts


Filling Station


Joined: Jan 2006
Posts: 7,034
Likes: 107
Hall Monitor
ChatMaster - 7,000
Offline
Hall Monitor
ChatMaster - 7,000
Joined: Jan 2006
Posts: 7,034
Likes: 107
Your stock wheels should do fine with modern tubeless tires. I put 205R75x15s on my 53. That's about the closest you'll get to the stock tire in diameter. A lot of folks run 215s which are a bit taller. If you go with the 205 be sure you're not getting trailer tires as 205 is a very common size for trailer tires. I don't know if "agile" driving is possible with the stock suspension.


VCCA Member 43216
Save a life, adopt a senior shelter pet.
1938 HB Business Coupe
1953 210 Sedan
1 member likes this: Boltgunner
Joined: Jan 2002
Posts: 30,700
Likes: 141
ChatMaster - 25,000
Offline
ChatMaster - 25,000
Joined: Jan 2002
Posts: 30,700
Likes: 141
I have done a dozen or more ( 20,000 miles) of long distance Interstate highway trips with my 1950 at speed up to 70 MPH with stock bias ply tires with no probem.
If you want domething a little better get s aet of radial tires.........thats all

Last edited by Chev Nut; 01/23/23 08:45 PM.

Gene Schneider
Joined: Jan 2023
Posts: 4
Grease Monkey
OP Offline
Grease Monkey
Joined: Jan 2023
Posts: 4
Thanks for the replies!

Where would I find the dimensions for the stock wheel, please?

Joined: Jan 2006
Posts: 7,034
Likes: 107
Hall Monitor
ChatMaster - 7,000
Offline
Hall Monitor
ChatMaster - 7,000
Joined: Jan 2006
Posts: 7,034
Likes: 107

Last edited by Tiny; 01/25/23 08:51 AM.

VCCA Member 43216
Save a life, adopt a senior shelter pet.
1938 HB Business Coupe
1953 210 Sedan
Joined: Dec 2007
Posts: 4,023
Likes: 99
ChatMaster - 4,000
Online Content
ChatMaster - 4,000
Joined: Dec 2007
Posts: 4,023
Likes: 99
Tiny’s advice about size for radials is right on target. The key limitation you will have is to get a tire that has the diameter you want without getting too wide.

The original bias ply tires were about what would be called an “88” series profile or aspect ratio. The largest ratio reasonably available in a 15” radial tire today is 75.

For example, the 205/75’s that Tiny has are just over 27” in diameter. A 6.70-15 is about 28 1/2” in diameter. It is about 6 3/4” in width where 205 is just over 8” in section width.

The radials work great on these cars. They just don’t look the same.


Rusty

VCCA #44680
Joined: Jan 2006
Posts: 7,034
Likes: 107
Hall Monitor
ChatMaster - 7,000
Offline
Hall Monitor
ChatMaster - 7,000
Joined: Jan 2006
Posts: 7,034
Likes: 107
I believe a 6.70-15 diameter is just under 27.5 if I remember right. It could vary depending on the manufacturer I suppose. The 205 radial is just over 27. The closeness is why I went with the 205 over the 215 to keep my speedometer accurate. The width difference sure makes a difference in slow speed turning. Almost makes me want to put power steering on the car. laugh


VCCA Member 43216
Save a life, adopt a senior shelter pet.
1938 HB Business Coupe
1953 210 Sedan
Joined: Dec 2007
Posts: 4,023
Likes: 99
ChatMaster - 4,000
Online Content
ChatMaster - 4,000
Joined: Dec 2007
Posts: 4,023
Likes: 99
Hi Tiny!

I forgot that little detail about steering effort especially at low speed! I could parallel park my ‘37 with bias ply tires but it took some effort and finesse to have enough room to let the car roll a little bit so it would steer.

I agree that the diameter varies by manufacturer. If you scan the Coker website you will find 6.70-15 tires can vary in diameter from 27 1/4” to 28 1/2”. The original Chevy spec was to use a tire with a rolling radius of about 13 3/8”, or about 748 revolutions per mile. That is the basis for the speedometer drive.

The key point is that using a radial the tire section will be wider to get a comparable diameter and rolling radius


Rusty

VCCA #44680
Joined: Jan 2023
Posts: 4
Grease Monkey
OP Offline
Grease Monkey
Joined: Jan 2023
Posts: 4
205/75 - does this size mate well with the stock wheel, or can you propose a different wheel?

Joined: Jan 2006
Posts: 7,034
Likes: 107
Hall Monitor
ChatMaster - 7,000
Offline
Hall Monitor
ChatMaster - 7,000
Joined: Jan 2006
Posts: 7,034
Likes: 107
They will work fine on an OEM wheel. It's the same wheel as on my 53.


VCCA Member 43216
Save a life, adopt a senior shelter pet.
1938 HB Business Coupe
1953 210 Sedan
Joined: Dec 2007
Posts: 4,023
Likes: 99
ChatMaster - 4,000
Online Content
ChatMaster - 4,000
Joined: Dec 2007
Posts: 4,023
Likes: 99
I agree that a 205/75R15 will work fine on the 15x5 rim. The minimum recommended rim width for a 215/75R15 is 5.5”.


Rusty

VCCA #44680
Joined: Jan 2023
Posts: 4
Grease Monkey
OP Offline
Grease Monkey
Joined: Jan 2023
Posts: 4
OK, we are about done here - for the stock 15 X 5 rim, what is the factory cap/trim that goes with this wheel? I'm still trying to learn the names of sources of parts...and, in this case, part numbers! Thanks!

Joined: Jan 2008
Posts: 366
Likes: 1
Backyard Mechanic
Offline
Backyard Mechanic
Joined: Jan 2008
Posts: 366
Likes: 1
I put the Coker 205/75 radials on my '50 stock wheels years ago and they were a great ride and handling improvement.

Attached Images
20220702_125841_HDR.jpg 20220702_130002.jpg 20220702_125855_HDR.jpg

Dean 50 - VCCA #44675
1 member likes this: Ed_Osier
Joined: Nov 2004
Posts: 1,113
Likes: 1
ChatMaster - 1,000
Offline
ChatMaster - 1,000
Joined: Nov 2004
Posts: 1,113
Likes: 1
Bolt--

You can buy the dog dish caps from: Chevs of the Forties, National Chevy Assoc, and the Filling Station. As you have a deluxe model, you might also want the beauty rings which are also available from these suppliers. The repros are good quality and even feature the painted bow tie on the caps. If you insist on originals, a good old junkyard will probably have some you can use as they were common to 51-53 models.

Just a note--on my stock rims, I had trouble getting a good seal with radials and ended up buying radial tubes available from Coker Tire. They work fine. I'm running bw 215-70R-15s on my 51 Special which are a little wider and look better than the 205s, and were used back in the day as RPO for taxis. (215-75R15s)


Rick

"Never time to do it right the first time, but always time to do it over."

Link Copied to Clipboard
Support The VCCA!

Enjoy the forum? Become a VCCA member! The World's Best Chevrolet and GMC Club!


Member Photos
1964 Chevrolet Impala SS
1964 Chevrolet Impala SS
by DreamChevy, February 17
My 1933 Chevy 2 Dr. Sedan
My 1933 Chevy 2 Dr. Sedan
by 1939Chevy1, November 24
Back on the road 79 years later
2 1927 Chevrolet Trucks
2 1927 Chevrolet Trucks
by 1927TRUCKS, June 7
Who's Online Now
3 members (Rusty 37 Master, 2 invisible), 94 guests, and 23 robots.
Key: Admin, Global Mod, Mod
Newest Members
NeilA, Jayhicks, Tomvanhouten, Dads29Chevy, Tractorman
18,308 Registered Users
Today's Birthdays
SabrinaKarras, Speedy1
Forum Statistics
Forums58
Topics59,071
Posts429,077
Members18,308
Most Online1,133
Jan 22nd, 2020
 

Notice: Any comments posted herein do not necessarily reflect the official position of the VCCA.

Powered by UBB.threads™ PHP Forum Software 7.7.5