Reproduction Parts for 1916-1964 Chevrolet Passenger Cars & 1918-1987 Chevrolet & GMC Trucks


Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Feb 2022
Posts: 112
Likes: 2
TG1931 Offline OP
Shade Tree Mechanic
OP Offline
Shade Tree Mechanic
Joined: Feb 2022
Posts: 112
Likes: 2
Just purchased a 1995 Corvette with automatic transmission. The selector plastic window is off center and is loose inside the housing. Took the center counsel out to take a look see. Doesn't appear it snaps or clues into place. Just suspends without support allowing it to slip out of position. Any suggested remedy? It just looks sloppy and unhappy with that appearance.

World's Greatest
 
Vintage Chevrolet Club of America
"The World's Best Chevrolet Club"
Joined: Feb 2022
Posts: 112
Likes: 2
TG1931 Offline OP
Shade Tree Mechanic
OP Offline
Shade Tree Mechanic
Joined: Feb 2022
Posts: 112
Likes: 2
Apparently nobody else with a Corvette with automatic transmission has had this issue? Hard to believe.

Joined: Nov 2001
Posts: 19,743
Likes: 59
ChatMaster - 15,000
Online Happy
ChatMaster - 15,000
Joined: Nov 2001
Posts: 19,743
Likes: 59
It might be better to find a Corvette site to pose your problem as they are focused on them. I suspect that there are not too many 1995 Corvette owners on this site.


How Sweet the roar of a Chevy four!
Joined: Feb 2022
Posts: 112
Likes: 2
TG1931 Offline OP
Shade Tree Mechanic
OP Offline
Shade Tree Mechanic
Joined: Feb 2022
Posts: 112
Likes: 2
Thanks but its a question regarding all C-4 Corvettes. It ran from 1982 - 1995. Must be millions out there. I will source a Corvette specific blog. Appreciated!

Joined: Feb 2022
Posts: 112
Likes: 2
TG1931 Offline OP
Shade Tree Mechanic
OP Offline
Shade Tree Mechanic
Joined: Feb 2022
Posts: 112
Likes: 2
Removing the center council was a real PITA but finally successful. The clear plastic window on the AT gear selector is held in place by four small screws into plastic nubs protruding down. My issue was all four nubs had snapped clean allowing the window to drop down and rattle inside the cavity below. Assume this must be a common issue with C-4 Corvettes. Glued all the nubs back with epoxy and it's holding for now. Certain just a short matter of time before they snap clean again. A horrible design flaw.


Link Copied to Clipboard
Support The VCCA!

Enjoy the forum? Become a VCCA member! The World's Best Chevrolet and GMC Club!


Member Photos
1964 Chevrolet Impala SS
1964 Chevrolet Impala SS
by DreamChevy, February 17
My 1933 Chevy 2 Dr. Sedan
My 1933 Chevy 2 Dr. Sedan
by 1939Chevy1, November 24
Back on the road 79 years later
2 1927 Chevrolet Trucks
2 1927 Chevrolet Trucks
by 1927TRUCKS, June 7
Who's Online Now
3 members (J Franklin, Peter_Gariepy, Chipper), 39 guests, and 39 robots.
Key: Admin, Global Mod, Mod
Newest Members
RichR, Johnbon35, TekuEntity, sammyrhoden, Nick_in_Manitou
18,267 Registered Users
Today's Birthdays
Bob_Hill, etnfrd67, sixyearsdown
Forum Statistics
Forums58
Topics58,938
Posts428,210
Members18,267
Most Online1,133
Jan 22nd, 2020
 

Notice: Any comments posted herein do not necessarily reflect the official position of the VCCA.

Powered by UBB.threads™ PHP Forum Software 7.7.5