Active Topics : Past 24 hours

You are not logged in. [Log In] Chat Homepage » Forums » Active Topics Past 24 hours

Birthday's

No birthdays today

VCCA Member's Photos

Member's Projects

Active Topics | Active Posts

Past 24 hours | Past 48 hours | Past 7 days

Forum

Subject

1949-54

1954 Generator by n2chev 18 minutes 53 seconds ago

I am rebuilding my 54 generator (#1100028) and while waiting for parts I installed a (1105009) polarized the reg and it works fine. My question is: what does this generator (1105009) fit? My book (1929-1954) does not list this number.

hopp

Chev CARS & Trucks - For Sale

1981 Chevy Impala orig paper trail Janesville on by karen81 49 minutes 48 seconds ago

4Dr Sedan Classic 47,000 original miles, clean, good condition no rust garage kept a/c,cruise control,am/fm etc 3.8 liter v6 original shipping papers from Janesville, Wi. dealer prep papers all papers ref warrenty etc $5,500 OBO

General Discussions

Re: Did you fill out a Survey ??? by AntiqueMechanic Today at 11:11 AM

I was contacted this AM by a member in a town close to me and he had just received his G&D. Not sure if he received the G&D based on a replacement copy or this was the one due at the first of the month. Obviously something happened for

1937-42

Re: 1941 radio antenna by mike41 Today at 09:48 AM

Ray knows what he is talking about.

To replace the antenna on my 41, I called Denny Turner in Florida {I think that his name}. He advertises in G&D, under parts for sale. Check out a few back issues you'll find his advertisement.
<

1929-32

Re: float for 32?? by tazmo Today at 09:17 AM

yep. I need a float.

PARTS - Wanted

Need.... by davidbaldwin Today at 08:23 AM

I am looking for the input shaft on the transmission on a 28 National.

Thanks

dbmuskrat@hotmail.com

Chevy Trucks

Re: 216 Manifold Questions by Chipper Today at 07:13 AM

The engines with manifolds were painted as the doggie wrote. However most restorers use a high temperature cast iron manifold paint on the exhaust manifold to keep it looking good and not rusty.

Mechanical - Engine, Trans, etc

Re: 28 engine rebuild by Chipper Today at 07:11 AM

If your bearings are pitted, either they are getting brittle or acid has attacked them. In both cases I would suggest getting your shells rebabbited and then line bore them to proper size with 4 0.002" shims per side. There are a few places that do

1912-1928

Re: AC speedometer (26-27) by Solan Today at 07:06 AM

Sending you a PM.

1949-54

Re: Tubes or Tubeless?? by glyn Today at 06:56 AM

Originally Posted By: Chev NutAll 1954 and prior rims were riveted..As back-roads said, it depends on the condition of the rim area where the tire makes contact. I would used bead sealer on any rims over 10 years old.
I am approaching 15,

1929-32

Re: running very rich??? by Chipper Today at 06:49 AM

What carburetor do you have on your 1932? Is it an original Carter W-1 212S? Or is it the later 235S? Or a replacement?

As Ray suggested check the float for leaks and adjustment. Also check to see if the float bowl cover is straight

1929-32

Re: Hot Water Heater Identification by 30USA1 Today at 06:08 AM

Thanks for all the imput. I have one of the tombstone style heaters for a 31. My car is a 1930 fourdoor. Purchased the heater for my display. I think now the other one is for the 33 to 35 Chevy. Thanks again for all your help. How do you put a

1912-1928

Re: 28 National pictures by davidbaldwin Today at 01:02 AM

I have read lots of schools is in session! What a great resource! You can't buy that type of information in a store!

I guess what I am most interested in is colors. I am not doing a frame off, but the things I do paint, close counts f

1929-32

Re: Ventilator Decal by oniz Yesterday at 10:09 PM

THANKS Guys! I think the little details add alot so maybe with a little luck the old Coupe will show real good.I'll try to post a picture soon.Thanks again,Stan

1955-57

Re: 1956 Chevrolet Powermatic Service Training Booklet by khardy Yesterday at 09:27 PM

Hi Chip,

On dry land for about a week. Going to miss this one Did catch some of Fay last week. Think this is going to be a very active Hurricane season for September. Looks like there are two possibles coming across the Atlantic now.

1937-42

Re: tire sizes by RichK Yesterday at 08:26 PM

Jim,

Yes, I have done a bunch of internet research. I have found several sites where people have made comments on tires plus a local VCCA member who has 4 cars and some of the cars have the tires that I have ordered.

Here is a

1949-54

Re: Seat Belts by Chev Nut Yesterday at 07:30 PM

I would measure from the mounting point, around a person sitting in the seat and over to the other mounting point. Then add 12"
If I rmember correctly I used the 72" in the front of my '50.
Didn't instasll rears but they would be much short

PARTS - Wanted

Re: 1928 engine main bearings by chevy b Yesterday at 07:26 PM

Mike,
I have a NORS center main and a NOS lower front half and a NOS upper rear half. All line bore type. If that is any help E-mail me bwbugay@aol.com

Mechanical - Engine, Trans, etc

Re: 261 chev motor--someone must have some info by Chev Nut Yesterday at 06:42 PM

The balancer is installed the same as any other 216-235 engine. The common practice that I use is to install bolts in the puller holes to avoid damaging the rubber between the halves of the balancer. The I use a large hammer to drive it on. It will

General Discussions

Re: Best one-liner you know? by ken48 Yesterday at 06:23 PM

After 50, if you don't wake up aching in every joint, you are probably dead!!

General Discussions

Missing August G&D ? by mike41 Yesterday at 04:59 PM

I'm sure everyone knows this but just in case, Jean Fink at Fink Printing {contact info in G&D} can often get you another copy of G&D.

So if your August G&D is AWOL you can get another one mailed to you by contacting "always on the job" Je

Page 1 of 1

Your Status

Please login in order to post a note or to reply to an existing post.